MG-Rover.org Forums banner

21 - 36 of 36 Posts

·
Registered
mg_tf
Joined
·
62 Posts
It was quite a while ago, so my recollection is a bit hazy. I may used the rubber seal off the old stat. Have tried that?
 

·
Registered
mgf
Joined
·
16 Posts
Discussion Starter #23
no worries , cheers luke, i will give the thermostat a trim with the grinder this weekend and cut it down enough to get the rubber seal on.

thanks
martin
 

·
Registered
mg_tf
Joined
·
205 Posts
Oh dear Luke, you are not serious about grinding the thermostat are you?

To me, the logic is simple :- if you have correctly dismantled everything correctly out of the assembly, and the replacement thermostat doesn’t fit, then it’s the wrong thermostat!
I would be spending my time trying to find out why it’s wrong/ getting another, rather than attacking the current one with a grinder.
Kind regards,
Austin.
 

·
Registered
mg_tf
Joined
·
62 Posts
That doesn’t sound right. I don’t recall it being an issue. I’ll see if I can find the original receipt that may give some details about the exact part.
 

·
Registered
mg_tf
Joined
·
62 Posts
Hi Martin, my apologies, I believe you need the GTS104 thermostat. This is 82C and should fit the housing without any mods. Rimmer Brothers have them for under £5.

Regards
 

·
Registered
mgf
Joined
·
16 Posts
Discussion Starter #27
ok, cheers luke/austin, i will go back to rimmers. only £5 so peanuts, luckily thermostat o ring washers over stretched so couldnt touch the thermostat this weekend waiting for the o rings to arrive.
 

·
Registered
mgf
Joined
·
16 Posts
Discussion Starter #28
hi
update - after installing the 82c degrees thermostat and checking all the rear water hoses for blockages i ran the car outside the house for about 1 hour idling and revving to 3000/4000 revs. heater got hot, radiator fan would kick in every now and then and needle stayed about 8 o clock on the gauge then all of a sudden after about 1 hour the temperature started to rise and the coolant started to boil even when i put heater fan on full while rad fan was running.

then i tried again the following day with the heater set to Cold and the car was fine, gauge stayed the same. i took it for a drive with the heater still on cold and no issue whatsoever so i am now at the conclusion the heater matrix is blocked.

will try back flushing next weekend if its not raining again, anyone know where to get to the heater coolant pipes? i seen the ones at the back of the engine but some users have said you can get to them underneath? i know if it need to change the heater matrix then its a dashboard out job.

thanks
martin
 

·
Registered
mg_tf
Joined
·
205 Posts
I’m sorry Martin, but I’m just not following your logic regarding a blocked heater core being the issue here. If you turn the heater control to cold then you are not allowing coolant to pass through the heater matrix - just as if it was blocked, or conversely, if it is blocked then it’s just like turning it off!
When you had it turned to hot, did the heater blow out hot air?
Did you bleed all 3 bleed points in order:- radiator, heater and then engine hose?
Kind regards,
Austin.
 

·
Registered
mg_tf
Joined
·
62 Posts
Hi Martin,

I tend to concur with Austin on the heater matrix not being the issue. I’m more suspicious of the front radiator. Here’s my logic. With the heater off, you have less water circulating in the circuit and the radiator and fan are able to dissipate the heat. However if the front radiator is partially blocked and with the higher volume of water circulating with the heater on, the partially blocked tad is unable to dissipate enough heat and the system boils over. Only a theory, but it’s worth removing the rad and checking the volume and flow rate through. You may be able to do this without removing the rad of course.

Good luck

Ps. I’m assuming the GTS104 thermostat was correct?
 

·
Registered
Joined
·
219 Posts
I've suffered from when a previous owner put that coppery coolant system leak seal gunk in my previous TF, perhaps as a 'permanent' leak fix :-(

Nether he nor the product were 'smart' imo and I'm sorry to say it doesn't seem to discriminate where to seal...
 

·
Registered
mgf
Joined
·
16 Posts
Discussion Starter #32
hi All

luke - thanks thermostat was perfect fit.

i understand all the doubts, agree doesnt seem to be logic in turning the heater to cold the car runs ok and doesnt overheat, only thing i have noticed when the heater was on hot and the car started to overheat there was always an air lock somewhere, either the heater would go cold and the car start to over heat, another time after driving it for 20 miles i turned the heater on it started to over heat and thats when i checked the outlet from rad and it was cold.

yes heater does run very hot when on. i am also bleeding via the correct 3 points. i will drive the car for the rest of the week with heater turned off and see, i do have my doubts and maybe you are correct, if its dry at the weekend i will do a reverse flush of the matrix, if still overheating rad removal and clean will be next.

cheers guys.
 

·
Registered
Joined
·
219 Posts
I've just read that jiggle valves serve to release trapped air to the expansion box side of the engine and that there's a second jiggle valve just below the cyl head on the rhs of the engine looking forward
hi All

luke - thanks thermostat was perfect fit.

i understand all the doubts, agree doesnt seem to be logic in turning the heater to cold the car runs ok and doesnt overheat, only thing i have noticed when the heater was on hot and the car started to overheat there was always an air lock somewhere, either the heater would go cold and the car start to over heat, another time after driving it for 20 miles i turned the heater on it started to over heat and thats when i checked the outlet from rad and it was cold.

yes heater does run very hot when on. i am also bleeding via the correct 3 points. i will drive the car for the rest of the week with heater turned off and see, i do have my doubts and maybe you are correct, if its dry at the weekend i will do a reverse flush of the matrix, if still overheating rad removal and clean will be next.

cheers guys.
 

·
Registered
Joined
·
219 Posts
Just a thought...
On the F/TF jiggle valves seem to serve the task of bleeding air from the inside to the outside of the engine/expansion tank (I think?). Apparently (apart from the img) there's a second jiggle valve just under the cyl head on the rhs of the engine looking back to front. I've never known about this before, yet alone 'cleared' mine, but could this be another area on your TF that doesn't allow an air pocket to clear - giving you these o/heating probs - I wonder? (In deference to the gunk in your t/stat)
(There's some interesting reading on this w/site...)
mgf.ultimatemg.com/group2/common_problems/hgf_pages/why_do_hgfs.htm

133892


Why do head gasket failures occur?


ttp://mgf.ultimatemg.com/group2/common_problems/hgf_pages/why_do_hgfs.htm
 

·
Registered
mgf
Joined
·
16 Posts
Discussion Starter #35
hi everyone,

thought i post an update. i have been running the car to station and back plus a few 30 mins trip around town and neighbouring towns for the last month now and i havent had any movement in the temp needle from one below half. Previously i would have expected to have a rise in temperature towards 3 quarters at least once a week in this time.

The last job i did was to back flush the heater matrix with the hose pipe, i didnt get chance to see any gunk come out so i dont know if the same gunk that had completely blocked the jiggle valve on the air filter side was present in the heater matrix.

the one thing i have noticed now is that the car now takes about 10 mins to warm up with the heater on, before when i purchased the car back in august one of the reasons i was convinced i had a issue was that the car warmed up to normally with 1 or 2 minutes with or without the heater on and this was always a concern before.

Whether its because the weather is colder now i am not sure but once i have taken on a long trip it might give a better idea as to if the heater matrix possibly being blocked was the cause.

thanks
martin
 

·
Registered
mg_tf
Joined
·
62 Posts
Hi Martin,

Tbat sounds like a good result. I'm guessing that you still have the 82C thermostat fitted, in which case it may take a fraction longer to get up
to temp over the 88C stat but 10 mins sounds right to me. I've been running an 82C stat o. My TF for 2 years now, but i relocated mine to the front, just behind the radiator. The logic being it will minimise the thermal shock to the head as there will be more blending of hot and cold before the stat opens. I dont use my car in the winter so Im not too concerned about the longer warm up time with more water circulating ahead of the stat.

Good job enjoy
 
21 - 36 of 36 Posts
Top